Are you looking for Real Time Systems old, previous or model question papers from M.G University Kerala? Hereunder is an original question paper of Real Time Systems for Seventh semester (07th/VII) B.Tech Applied Electronics and Instrumentation. This question paper was asked in the year Nov 2013. Read the contents below.
M.G University, Kerala
B.Tech Degree Examination, November 2013
Seventh Semester
Branch : Applied Electronics and Instrumentation
AI 010 706L02 - REAL TIME SYSTEMS (Elective-1)
(New Scheme-Regular/Improvement/Supplementary)
Time: Three Hours
Maximum : 100 Marks
Answer all questions.
Part A
Each question carries 3 marks.
1. What is meant by polled loop system?
2. Define the term “EDF”.
3. What is meant by Synchronization?
4. Define fault tolerance.
5. What are the characteristics of a real time systems?
(5 × 3 = 15 marks)
Part B
Each question carries 5 marks.
6. Give the structure of real time system and explain.
7. Explain about next fit algorithm.
8. Explain message sending topologies.
9. Explain different causes of failure of the system.
10. What are all the databases used for hard real time systems?
(5 × 5 = 25 marks)
Part C
Each question carries 12 marks.
11. Explain the classification of real time systems. Bring out the real time design issues.
Or
12. Briefly explain the characteristics and working of an interrupt driven systems.
13. With an example, explain Performance measures for real time systems.
Or
14. Explain any two multiprocessor scheduling algorithms.
15. Discuss in detail about network architecture issues and protocols.
Or
16. With an example, explain (i) Round robin, (ii) Fault tolerant routing.
17. Explain in detail about fault types,fault detection and containment.
Or
18. Write a short note of the following:-
(i) Master chain model.
(ii) Fault latency.
(iii) Software error models.
19. Discuss in detail about real time databases and its characteristics.
Or
20. Write a short note of the following:-
(i) Disk Scheduling algorithm.
(ii) Maintaining serialization constituency.
(5 × 12 = 60 marks)
M.G University, Kerala
B.Tech Degree Examination, November 2013
Seventh Semester
Branch : Applied Electronics and Instrumentation
AI 010 706L02 - REAL TIME SYSTEMS (Elective-1)
(New Scheme-Regular/Improvement/Supplementary)
Time: Three Hours
Maximum : 100 Marks
Answer all questions.
Part A
Each question carries 3 marks.
1. What is meant by polled loop system?
2. Define the term “EDF”.
3. What is meant by Synchronization?
4. Define fault tolerance.
5. What are the characteristics of a real time systems?
(5 × 3 = 15 marks)
Part B
Each question carries 5 marks.
6. Give the structure of real time system and explain.
7. Explain about next fit algorithm.
8. Explain message sending topologies.
9. Explain different causes of failure of the system.
10. What are all the databases used for hard real time systems?
(5 × 5 = 25 marks)
Part C
Each question carries 12 marks.
11. Explain the classification of real time systems. Bring out the real time design issues.
Or
12. Briefly explain the characteristics and working of an interrupt driven systems.
13. With an example, explain Performance measures for real time systems.
Or
14. Explain any two multiprocessor scheduling algorithms.
15. Discuss in detail about network architecture issues and protocols.
Or
16. With an example, explain (i) Round robin, (ii) Fault tolerant routing.
17. Explain in detail about fault types,fault detection and containment.
Or
18. Write a short note of the following:-
(i) Master chain model.
(ii) Fault latency.
(iii) Software error models.
19. Discuss in detail about real time databases and its characteristics.
Or
20. Write a short note of the following:-
(i) Disk Scheduling algorithm.
(ii) Maintaining serialization constituency.
(5 × 12 = 60 marks)
0 comments:
Pen down your valuable important comments below